DPF 510GT/MT

Digital Print Pressure-Sensitive Vinyl Film

DPF 510GT/MT is a 100 microns monomeric film with a gray, solvent-based pressure-sensitive adhesive.

The two-sided polycoated liner provides excellent lay-flat properties. The high-quality adhesive provides far superior adhesion and cohesion properties than water-based adhesive. DPF 510GT/MT is available in a white gloss finish.

DPF 510GT/MT is rated for outdoor durability up to 3 years (unprinted). Printed durability is dependent on the ink system used.

Applications & Features

  • Short-term promotional and display graphics, including kiosks, POP displays, real estate signage and interior floor graphics*
  • Excellent printability on Eco-Solvent, Solvent and Latex print systems
  • Ideal for interior and exterior applications on flat surfaces

*When used with Series 3510 Matte.

Performance & Physical Data

Property Test Methods Typical Value
Surface Finish Gloss Meter 60° Reflection Matte: Up to 30 Gloss Units
Gloss: 70 to 90 Gloss Units
Thickness Micrometer, Federal Bench Type 100 microns
Tensile Strength Tensile Tester with 51 mm jaw separation; crosshead speed of 5.1 mm/s, web direction ≥ 2.7 kg/cm
Elongation Instron Tensile Tester as above ≥ 200%
Shelf Life (In Box) Ideal Storage Temperature 21°C and 50% relative humidity 1 year from factory shipment
Application Temperature Range On clean, dry substrate 10°C to 32°C
Service Temperature Range On clean, dry substrate -29°C to 65°C
Dimensional Stability 70°C, 48 hours 0.25 mm
Peel Adhesion PSTC-1, 15 min, 21°C 0.36 kg/cm
Liner Release TLMI Release at 90°, 760 cm/min 7.9 g/cm

FLOOR APPLICATIONS

DPF 510 GT/MT is recommended for short-term interior floor applications such as smooth floors, sealed concrete, ceramic tile, waxed vinyl flooring, sealed wood, marble and terrazzo, when used with Series 3510 Matte, which is approved under the European Standard Certification EN 14041 for slip-resistance for Floor Graphic Materials. To determine the best product for application Arlon always recommends testing prior to using the above products on the actual surface as product performance can vary greatly depending on the surface type, level of foot traffic, elemental exposure and floor condition. Due to these variables, Arlon only warrants the material(s) for standard manufacturers defect and is unable to offer a warranty for the performance or clean removability of these products for floor graphic applications.
Please refer to Arlon’s Installation Guide for detailed techniques and best practices.

EN 14041 - Resilient, textile and laminate floor coverings
Determination of the anti-slip properties (EN 14041): Determination of the dynamic coefficient of friction of floor materials in accordance with EN 14041.

TERMS & CONDITIONS

The following is made in lieu of all warranties expressed or implied:

All statements, technical information and recommendations published by Arlon relating to Arlon products are based on tests believed to be reliable and within the accuracy of the equipment used to obtain the specific values. Their accuracy or completeness is not guaranteed and Arlon makes no warranty with regard thereto. Seller’s and manufacturer’s only responsibility shall be to replace any quantity of the product proved defective. Seller and manufacturer shall not be liable for injury, loss or damage, direct or consequential, arising out of use or the inability to use the product. Nor shall seller or manufacturer be liable for any costs or expenses incurred in the processing or printing on the product. Before using, user shall determine the suitability of the product for its intended use. User assumes all risk and liability of every nature in connection therewith. No statements or recommendations other than those contained in the technical information published by Arlon shall have force or effect unless contained in an agreement manually signed by the officers of seller and manufacturer.

Copyright © Arlon Graphics, LLC. All Rights Reserved.